Superseded 5.280HE
Part Numbers
|
Part Description |
Part Numbers |
|
Oil Filter |
603003 |
|
Fuel Filter |
622350 |
|
Impeller |
544310 |
|
Gasket, Impeller |
614616 |
|
Seal, W/Pump |
614516 |
|
V Belt |
301448 |
|
O-Ring, Heat Exchanger |
KSAV02 |
|
Anode, Engine |
494635 |
|
Anode, Selva Sail Drive (<2003) |
310045 |
Periodic Maintenance
| CHECK |
EVERY DAY |
AT 20 HRS |
100 HRS |
200 HRS OR EVERY YEAR |
400 HRS OR EVERY 2 YRS |
|
Oil Levels (Engine & Gearbox) |
x |
||||
|
Battery Charge (indicator) |
x |
||||
|
Water Temperature & Operation |
x |
||||
|
General Sealing |
x |
||||
|
Battery Electrolyte level |
x |
||||
|
Operation of the Controls |
x |
||||
|
Belt Tension |
x |
x |
|||
|
Valve Adjustment |
x |
x |
|||
|
Starter & Alternator Mountings |
x |
||||
|
Tightness of Screws and Assemblies |
x |
x |
|||
|
Sea Water Pump |
x |
||||
|
Engine Mounts and Alignment |
x |
||||
|
Injector Calibration |
x |
||||
|
Sea Water Strainer |
x |
||||
|
Thermostat (to be cleaned) |
x |
||||
|
Coolant level in Heat Exchanger |
x |
||||
|
Zinc Anode |
x |
||||
|
Air Filter |
x |
||||
|
CLEAN |
|||||
|
Heat Exchanger Tube Stack |
x |
||||
|
REPLACE |
|||||
|
Oil Filter |
x |
x |
|||
|
Fuel Filter |
x |
||||
|
Oil (Engine & Gearbox) |
x |
x |
|||
|
Coolant |
x |
x |
|||
|
Primary Fuel Filter |
x |
||||
|
O-Rings, Heat Exchanger |
x |
x |
|||
|
Impeller |
x |
||||
|
V Belt |
x |
Technical Data
ENGINE SPECIFICATION
Number of cylinders : 5
Displacement : 2746 cc
Bore - Stroke : 87 X 9204 mm
Compression ratio : 23/1
Max. pressure difference between cyl. : 10%
Compression pressure : 36 to 38 kgF/sq.cm.
Maximum speed without load : 3050 T/mn
Maximum RPM in load : 2800 T/mn
Idle RPM in forward gear : 800 T/mn
Max. torque : 190 Nm
Firing order : 1 - 3 - 5 - 4 - 2
Rotation : Anti clockwise
INJECTION
Type of injector : DNOPD95
Fuel injection pressure : BODCH K type mini
Injection pump manufacturer : 137.3 to 147.1 bar
Injection timing : 19° before top dead center
TIGHTENING TORQUE
Arm head cover cap nuts : 6.9 to 8.8 Nm
Cylinder head bolts : 93.1 to 98 Nm
Flywheel bolts : 98.1 to 107.9 Nm
Connecting rod bolts : with coll.: 36.3 to 41.2Nm
without coll.: 44.1 to 49 Nm
Rocker arm bracket nuts :22.5 to 27.5 Nm
Main bearing caps bolts : 46.1 to 50.9 Nm
Main bearing caps bolts : 68.6 to 73.5 Nm
Nozzle holder assembly : 49 to 68.6 Nm
Glow plugs : 19.6 to 24.5 Nm
LUBRIFICATION
Oil pressure at idle RPM : 0.49 bar
Oil pressure at maximum load : 3.0 to 4.5 bar
Recommended oil : MIL-L-2104-C
Oil pan capacity :
- mini : 9 l
- maxi : 10.5 l
Gearbox model : HURT HBW 250/TMC
Oil capacity : 0.75 l / 1.6 l
Recommended oil : ATF / 15W40
DIAGRAMS
Valve clearance (cold) :
Inlet : 0.18 to 0.22
Exhaust : 0.18 to 0.22
Valve recessing : + 0.05 to - 0.15 mm
PISTON RINGS
Piston ring gap :
Piston top compression : 0.30 to 0.45
Intermediate :
Oil control : 0.25 to 0.45
CYLINDER HEAD
Cylinder head surface flatness : 0.05 mm
SEA WATER PUMP
Water flow : 65 l/mm
GLOW PLUGS
Resistance :0.8 ohm
Previous page: Superseded 4.220HE
Next page: Superseded 5.250TDI